Plumbing Essentials: A Prerequisite for When Installing a Bathtub
Plumbing Essentials: A Prerequisite for When Installing a Bathtub
Blog Article
The article following next relating to Installing A Bathtub is definitely informative. Don't miss out on it.
Setting up a bathtub isn't specifically brain surgery, however it does need solid plumbing, carpentry, and also sometimes, tiling abilities. Replacing an old bath tub with a new one is likewise a moderately challenging task. If the old tub is conveniently obtainable, the project can relocate speedily; if you have to open up a wall to remove the old tub and also place the new tub, the job is much harder. In either situation, the job is within a home handyman's abilities, although you will need an assistant to move out the old bathtub as well as embeded in the brand-new one. Make sure you have actually qualified on your own for the task as well as fit attempting it. Instead of hiring a specialist to take control of a halfway-completed job, it is better to consider employing one before you begin. Opportunities are you may require an expert plumber to make tube links.
This write-up will aid you mount a new tub in your bathroom if you have already acquired a new bathtub and don't require to change the plan of your previous water supply pipelines.
Your devices and product list ought to comprise the following:
Removing Old Touches
If you require to change old taps with new ones as a part of your setup, then the first thing you must do is separate the water supply. After doing so, switch on the taps to drain any water remaining in the system. The procedure of removing the existing faucets can be rather problematic because of the restricted accessibility that is usually the case.
Use a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a fabric prepared for the staying water that will certainly originate from the pipes. Once the supply pipes have actually been gotten rid of, utilize the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single taps from transforming during this process. Once the taps have been eliminated, the holes in the bath/basin will certainly have to be cleaned of any old sealing compound.
Before proceeding to fit the new taps, contrast the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will require a plastic connector to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet and the other end supplies a link to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly need decreasing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making sure that the washers remain in place in between the tap as well as the sink. Safeguard the faucet in place with the maker provided backnut. Once the tap is safely in place, the supply pipes can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with normal tap connectors. The previous kind needs to be connected to the faucet finishes first, tightening only by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Setting up the Bathtub
Making use of both wooden boards under its feet, place the tub in the required placement. The wooden boards are practical in evenly spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto four small factors.
The next goal is to guarantee that the tub is leveled all round. This can be accomplished by checking the spirit level and also readjusting the feet on the bath tub till the level reviews degree.
To mount taps, fit all-time low of the furthest flexible tap port to the ideal supply pipe by making a compression join; after that do the same for the various other tap.
Switch on the water and inspect all joints as well as new pipework for leaks as well as tighten them if needed. Load the bath tub and likewise examine the overflow outlet and the normal electrical outlet for leakages.
Ultimately, take care of the bath paneling as defined in the producer's user's manual. Tiling and also sealing around the bathtub ought to wait until the tub has actually been utilized a minimum of when as this will settle it right into its last position.
Planning for the Installation
First of all, the sustaining structure provided with the bathroom needs to be fitted (if required) according to the producer's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is essential to ensure that if the tap comes with a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps device to avoid stress on the bathtub.
Fit the flexible faucet adapters to the bottom of the two faucets utilizing 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet via the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you use every one of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to currently prepare to be fitted in its final setting.
Tiling Around the Bathtub
In the area where the bathroom meets the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is essential as the installation can relocate enough to split a rigid seal, creating the water to permeate the wall between the bathroom and also the tiling, resulting in problems with dampness and feasible leakages to the ceiling below.
You can select from a selection of coloured sealants to blend in your fixtures and also fittings. They are offered in tubes and also cartridges, as well as can sealing voids approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with spins of soaked paper or soft rope. Remember to always fill the bathtub with water prior to securing, to permit the motion experienced when the bathtub remains in usage. The sealer can fracture rather very early if you do not think about this activity before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise conveniently available on the marketplace. It is recommended to fit the floor tiles utilizing waterproof or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a keen reader about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I think sharing that excerpt was a smart idea. Sharing is good. You never know, you may be helping someone out. Thank you so much for your time invested reading it.
Act fast, Call us! Report this page